|
Below is a list of vPro-AMT enabled platforms that have been validated by SyAM Software.
- Asus P5B-VM DO
- Asus P5E-VM DO
- Dell Optiplex 755
- Dell Optiplex 760
- Dell Optiplex 960
- ECS Q45T-M
- Foxconn Q45M
- Gigabyte Q35M-S2
- Gigabyte Q45M-S2
- Gigabyte Q57M-S2
- Hewlett Packard DC7700
- Hewlett Packard DC7800
- Intel SE7230NH-1
- Intel D945GTP
- Intel DQ35JO
- Intel DQ45CB
- Intel DQ45EK
- Intel DQ57TM
- Intel DQ965CO
- Intel DQ965GF
- Intel DQ965WC
- Intel D945GCZ
- Intel S3000AH
- Lenovo Thinkcentre 8808
Below is a list of Intel® motherboards and their BIOS levels that have been validated by SyAM Software.
| AMT Board
| Bios Version
|
| DQ57TM |
0038 |
| DQ35JO |
0757 |
| DQ45CB |
0061 |
| DQ45EK |
0061 |
| DQ 965GF / DQ965WC /DQ965CO |
CO96510J.86A.6094.2009.0406.1239 CO96510J.86A.6088.2008.1201.0056 CO96510J.86A.6002.2007.1125.2356 CO96510J.86A.5947.2007.0725.1741 CO96510J.86A.5869.2007.0327.0132 CO96510J.86A.5595.2006.1227.1649 CO96510J.86A.5564.2006.1122.1346 CO96510J.86A.4713.2006.0828.1752 CO96510J.86A.4462.2006.0804.2059 |
| D945GCZ |
NT94510J.86A.3943.2006.0707.1405 NT94510J.86A.3996.2006.0908.1329 |
| D945GTP |
NT94510J.86A.3943.2006.0707.1405 NT94510J.86A.3996.2006.0908.1329 |
| SE7230NH-1(NOBHILL2) |
NH72310J.86B.1179.2006.0508.2328 |
| S3000-AH |
S3000.86B.02.00.0041.042020071551 no IDE-r support with this BIOS |
Below is a list of Non-Intel® motherboards and their BIOS levels that have been validated by SyAM Software.
| AMT Board
| Bios Version
|
Lenovo Thinkcentre AMT SOL BIOS Settings Baud Rate = 57.6k Console Type = VT100 Flow Control = XON/XOFF |
2MKT36AUS |
| Asus P5B-VM-D0
| 901 7/19/2007 |
| Asus P5E-VM-D0
| 0506 |
| HP DC7700 |
786E1 v01.05 |
| HP DC7800 |
786F1 v01.28 |
| Dell Optiplex 960 |
BIOS A06 |
Dell Optiplex 760
| BIOS A07 |
| Dell Optiplex 755 |
BIOS A08 Note - when using the One-Touch Provisioning you must use a FAT formatted 128MB USB drive |
| Gigabyte Q57M-S2 |
BIOS F3i |
| Gigabyte Q45M-S2 |
BIOS FCv |
| Gigabyte Q35M-S2 |
BIOS F3r |
When Adding Systems to the System Areal Manager, we recommend that you keep the IP address range minimal. This will minimize the time to adding all of the managed nodes to the System Area Manager.
When using Intel AMT in a static IP address mode we recommend that you don't keep the IP address of the Intel AMT system the same as the operating system.
The AMT enabled Ethernet port on the S3000AH server is port 1, which is located above the 2 USB ports.
When using IDE-R to boot into Windows Setup we recommend using an ISO image and not the CD
|